Regulation No 26 of the Economic Commission for Europe of the United Nations (UN/ECE) — Uniform provisions concerning the approval of vehicles with. ECE R26 Regulation (03 Series, ) “The uniform regulations on vehicle chapter and section numbering betw een this standard and the ECE R ECE UNIFORM PROVISIONS CONCERNING THE APPROVAL OF: VEHICLES WITH REGARD TO THEIR EXTERNAL PROJECTIONS Incorporating.

Author: Moogum Doukree
Country: Great Britain
Language: English (Spanish)
Genre: Software
Published (Last): 25 May 2006
Pages: 74
PDF File Size: 19.31 Mb
ePub File Size: 13.20 Mb
ISBN: 469-6-53022-940-6
Downloads: 87272
Price: Free* [*Free Regsitration Required]
Uploader: Mikazragore

The wheel rim is fixed rigidly to the test bench, and a bending moment M b is applied to the hub mounting area i. UN R36 Bus Construction. Expand all Collapse all. In some cases, the provisions permit extensions of current approvals based upon previous requirements for example, to allow for replacement parts. The ends of the bumpers shall be turned in towards the external surface in order to minimise the risk of fouling.

Draft new Regulation No. Tests to be carried out should the maximum permitted wheel load subsequently increase. Uniform Provisions Concerning the Approval of Pneumatic Tyres for Motor Vehicles and their Trailers This rule applies primarily, but not exclusively, to tires for use on passenger cars and their trailers.

Certificates and licenses

An approval number shall be assigned to each type approved. This site uses cookies to improve your browsing experience.

Supplements are used for other significant changes, such as clarifying the f26 or to expand the regulation to cover additional products i. UN R Partitioning Systems. In the case where negative results are recorded during one of these visits, the Type Approval Authority shall ensure that all necessary steps are taken to re-establish the conformity of production as rapidly as possible. There shall be affixed, conspicuously and in a readily accessible place specified on the approval form, to every separate technical unit conforming to a type approved under this Regulation, an international approval mark consisting of: Regulation on uniform provisions concerning the approval of enhanced Child Restraint Systems used onboard of motor vehicles.

  BEHRINGER MICROMIX MX400 PDF

If the various clearances on the vehicle manufacturer’s replacement wheel are less than those given above, then these can be accepted.

Translation of “Regulation ECE-R26” in Spanish

Jacking Brackets and Exhaust Pipes 6. Air Intake and Outlet Flaps 6. The competent authority which has granted type approval may at any time verify the cee control methods applicable to each production unit.

The approval mark shall be clearly legible and be indelible. The competent authority shall verify the existence of satisfactory arrangements for ensuring effective control of conformity of production before type approval is granted. Uniform provisions concerning the approval of Retrofit Emission Control devices REC for heavy duty vehicles, agricultural and forestry tractors and non-road mobile machinery equipped with compression ignition engines WP.

Uniform Provisions Ecw the Approval of Motor Cycles with regard to Noise The proposal for the 04 series of amendments, adopted at the June Forum session, will be posted as Revision 2 to the regulation pursuant to the completion of administrative formalities.

Regulation ECE-R26 – Translation into Spanish – examples English | Reverso Context

Material Tests Aluminium f26 a, c, e Magnesium alloy a, c, e Steel a, b, d a Chemical analysis of the raw-material. Date of report issued by that service: The approved wheel when fitted to the vehicle, together with any necessary wheel accessories, shall not create any danger. In the case where wheel accessories are provided, any necessary special tools for mounting and demounting shall also be provided. UN R Replacement Airbags. The dimension exe a gap r6 space between rce of a grille shall be determined by the distance between two planes passing through the points of contact of the sphere and perpendicular to the line joining those points of contact.

UN R37 Filament Lamps. UN R Retrofit Emissions. Protective strips or shielding on the external surface shall not be subject to the requirements of paragraph 6. Analysis of the metallurgic defects and of the test-pieces structure taken from the hub mounting area and in the disc to rim transition area or in the failure zone if any. The nominal rim diameter, nominal rim width and nominal inset of ECE-approved wheels shall be the same as the manufacturer’s replacement wheel.

  COMPLICACIONES DE ABSCESO HEPATICO AMEBIANO PDF

The approval granted in respect of a type of wheel pursuant to this regulation may be withdrawn if sce requirements set forth above are not met or if a wheel bearing the approval mark does not conform to the type approved. Regarding wheel bolts, dce and studs, the length of thread engagement shall be the same as achieved by the vehicle manufacturer’s replacement wheel and wheel fixings. Trade name or mark of the vehicle: All the necessary steps shall be taken to re-establish the conformity of the corresponding production.

In the case where the calliper is inside the vehicle manufacturer’s replacement wheel calliper, a check shall be carried out of wheel operating clearance with respect to brake, suspension and steering components and general under body components, taking into account the effect of wheel balance weights. Figure 3 shows an example of the use of this procedure. An approval number shall be assigned e26 each vehicle type approved.

This regulation was established in parallel with the 08 series of amendments to UN R Annex 2 — Arrangement of the Approval Marks. Penalties for Non-conformity of Production Scope and purpose 2.

The administrative provisions include a date of “entry into force” of each regulation or amendment. NET Our online subscription service, offering immediate access to our extensive library of global vehicle regulations, standards and legislation.

UN R46 Indirect Vision. With regard to the design, inset, ecr designation wheel fixing PCD and spigot mounting diameter, correspond to that of an OE-wheel, but wheel contour, material and so on, may be different; 2.

Uniform Provisions Concerning the Approval of: Its first two digits at present 03 corresponding to the 03 series of amendments shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation at the time of issue of the approval.