FRENIC-Lift. FRENICG11S/P11S. FRENICVG7S. User’s Manuals and Technical Information. FRENIC-Multi User’s Manual. FRENIC-Eco User’s. FRENIC-Lift is an inverter designed to drive a three-phase induction motor ( hereafter For details about this product, refer to the FRENIC-Lift User’s Manual that. The FRENIC-Lift Series of exclusive AC Drives for operation of elevators are FRENIC-Lift AC Drives are available in a series with capacities ranging from

Author: Vudokus Tygogal
Country: South Africa
Language: English (Spanish)
Genre: Health and Food
Published (Last): 7 October 2016
Pages: 262
PDF File Size: 2.60 Mb
ePub File Size: 1.69 Mb
ISBN: 224-3-35573-469-3
Downloads: 4196
Price: Free* [*Free Regsitration Required]
Uploader: Fem

Each function code consists of a 3-letter string. Follow the procedure below for wiring and configuration of the inverter. For the motor, check the rated values printed on the nameplate of the motor. For the tuning procedure, refer to the instruction manual of the option card.

To print the manual completely, please, download it. Page 81 [ 24 ] Out of control speed Problem An out of control error PG failure occurs between the speed command and the speed feedback. Page 40 Table 2.

Possible Causes What to Check and Suggested Measures 1 No power supplied to the Check the input voltage, output voltage and interphase voltage unbalance. Table of Contents Add to my manuals Add.

Page 61 L codes: Recommended Wire Sizes 2. Manua terminals G Be sure to ground either of the two grounding terminals for safety and noise reduction.

  FORTINBRAS LEE BLESSING PDF

The operation level and thermal time constant can be set. Driving gener- When high starting torque is required or quick acceleration or deceleration al-purpose motor Selecting is required, select an inverter with a capacity one size greater than the inverter standard.

Tuning offset angle of the magnet pole Before to proceed to running a synchronous motor, be sure to tune offset angle of the magnet pole. Init ialize all function code data to t he factory defaults H04 Auto-resetting 0: Enable data prot ection Note: The first letter is an alphabet that identifies its group and the following two letters are numerals that identify each individual code in the group.

Fuji Electric FRENIC-Lift series Instruction Manual

U, V and W respectively and that the grounding wires are connected to the ground electrodes correctly. Disable Times Times 1 to Terminal board illustrated in except Figure A. Page 19 3 Mounting direction Horizontal layout is recommended when two or more inverters are to be installed in an equipment or enclosure. The two terminals prepared for grounding, which are indicated by the symbol G in Figures A to C, make no distinction between the power supply side primary circuit and the motor side secondary circuit.

The inverter connector RJ supplies the power to the keypad through the extension cable rfenic keypad. Using this adapter greatly Brake control by time 2: All products and company names mentioned in this manual are trademarks or registered trademarks of their respective holders. Page 30 Grounding terminals G Be sure to ground either mqnual the two grounding terminals for safety and noise reduction. When the dielectric strength test is necessary, contact your Fuji Electric representative.

  FR307 DATASHEET PDF

If any of the manal listed below occur, take an appropriate measure against them. Page In no event will Fuji Electric Co. Refer to Chapter 5, Section 5. Icons Ffrenic following icons are used throughout this manual.

,anual not hold covers or individual parts only. Marks to classify these situations in the torque control column of the function code table on the following pages as shown below.

FUJI ELECTRIC FRENIC-LIFT SERIES INSTRUCTION MANUAL Pdf Download.

Maximum speed F03 2 The reference torque bias follows the input voltage level on terminal [12]. You need to replace the option card. In no event will Fuji Electric Co. For the braking resistor built-in type, refer to the next page. Page 22 3 For inverters with a capacity of 30 kW or above Removing and mounting the cover To remove the front cover, loosen the four fastening screws, hold it with both hands, and slide it upward.

Doing so could cause fire.